Wilkerson Instrument Co. Homepage A World of Signal Conditioning & Process Control Instrumentation Products


FR1020
DC INPUT, FIELD RANGEABLE
DUAL LIMIT ALARM,
LATCHING OR NON-LATCHING

FEATURES
bulletAllows Inputs to ±256 V or ±100 mA
bullet16 mV or 0.8 mA Minimum Input Span
bulletRed and Green LED Alarm Status Indicators
bulletAdjustable Deadband
bulletProvides Relay Contact Closures at Preset DC Input
bulletConfigure Alarms as HI/HI; HI/LO; LO/LO
bulletAlarms Normal or Reverse acting
bulletConfigure as Latching Alarm
bulletFully Labeled Jumper Positions For Easy Range and Configuration Settings
bulletChoice of Power Options
bulletSize, Pinouts, and Performance Identical to MM1020
bulletPermanent Warranty


DESCRIPTION

The FR1020 monitors a DC input signal and provides two sets of SPDT, 5 A alarm relays with two independently adjustable setpoints. Each setpoint has a set of red/green LEDs to indicate alarm status. The configuration of each alarm relay is user-settable as follows:

High or Low - High selects alarm on an increasing signal. Low selects alarm on a decreasing signal.

Normal or Reverse - Normal position selects fail-safe operation (loss of power will result in alarm condition).  The relays are energized in the non-alarm condition.  When the setpoints are exceeded, the relays de-energize.  Selecting the reverse position reverses this logic.

Deadband or Latching - Deadband selects two independently adjustable deadband controls. Deadband for each alarm is adjustable from 0.1% to 100% of the input span. The deadband is symmetrical about the setpoint. With latching selected the alarms will latch when a setpoint is exceeded, and can not be reset unless the input no longer exceeds a setpoint. Reset may be accomplished by remote contact closure or by momentary power interruption. (Several reset inputs may be tied to one reset contact, but note that all negative inputs will be tied together.) The module includes filtering and conditioning to reduce susceptibility to transients and noisy operations.

MOUNTING

The module is designed to plug into a standard 11-pin relay socket. Part number MP011 is a molded plastic socket suitable for mounting on a flat surface or in a 2 3/4 inch wide PVC snap track (TRK48). Use CLP-1 hold-down clip if needed. A Killark HK series explosion-proof housing with dome and 11-pin socket is available (HKB-HK2D-11). DIN rail mount socket (P/N DMP011) fits 35mm rail.


SPECIFICATIONS

INPUTS                              
Limits
  any voltage between
  -256 and +256 VDC

  any current between
  -100 and +100 mA

Span (Selectable Ranges)
Voltage
16-32 mV
32-64 mV
64-128 mV
128-256 mV
256-512 mV
.5-1 V
1-2 V
2-4 V
4-8 V
8-16 V
16-32 V
32-64 V
64-128 V
128-256 V 		Current
.8-1.6 mA
1.6-3.2 mA
3.2-6.4 mA
6.4-12.8 mA
12.8-25 mA
25-50 mA
50-100 mA

Offset
± 0, 25, 50, 75, 100% of F.S.

INPUT IMPEDANCE
 Voltage
  1 megohm

Current
  20 ohms

SETPOINT
0 to 100% of span

DEADBAND
0.1% to 100% of span

 LATCHING ALARM
 Reset by remote contact closure
or by momentary power interruption

RESPONSE TIME
 20 ms typical

ACCURACY
±0.1% of span

COMMON MODE REJECTION
 120 dB, DC to 60 Hz

RELAY CONTACTS
 Two spdt
Resistive Load:
  5 A max, 150 W max,
  240 VAC max, 30 VDC max

Inductive Load:
  1/8 HP max at 120/240 VAC

OPERATING TEMPERATURE
 14°F to 140°F
-10°C to  60°C

TEMPERATURE STABILITY
±(0.02% of span +30 micro V)/°C max

POWER
 115 VAC ±10%, 50/60 Hz
  (2.5 W max)
230 VAC ±10%, 50/60 Hz
  (2.5 W max)
24 VAC ±10%, 50/60 Hz
  (2.5 W max)


(DC Power Option)
  24 VDC (limits 21-32 VDC)
    (2.5 W max)
  Isolation, DC power supply
  to input common:  100 megohm


CONNECTIONS
 Power, AC L1 or DC+
Latch Reset
Power, AC L2 or DC-
Input +
Input - 
Relay Set 1 NO
Relay Set 1 C
Relay Set 1 NC
Relay Set 2 NO
Relay Set 2 C
Relay Set 2 NC		 PINS
1
2
3
4
5
6
7
8
9
10
11